PROFESSIONAL ETHICS & HUMAN VALUES

NOORUL ISLAM COLLEGE OF ENGG, Kumaracoil
Common to AERO, ECE & Mech
2 MARKS & Big QUESTION ANSWERS
GE 1301 Professional Ethics & Human Values
Fifth Semester
Prepared by : Robin Diwahar, AERO
Dev. R. Newlin, ECE
Edwin Raja Dhas, Mech
Electronics &Communication Engineering
Subject code: EC 1011
Subject: Television and Video Engineering
(For seventh semester ECE )
2 Mark Questions and Answers
1. Mention the major function of the camera tube?
The major function of the camera tube is to convert an optical image into
electrical signals.
2. Define visual acuity?
Visual acuity can be defined as the ability of human eye to resolve finer
details in a picture
3. What do you refer by persistence of eye?
The persistence of eye refers to the storage capability of the human eye
4.Define luminous intensity?
It is the measure of light intensity responsible for stimulating visual
sensation.
5.Define aspect ratio?
Aspect ratio can be defined as the ratio of width to height of the picture
frame. For television, it is standardized as 4:3.
6.Define luminous flux?
Luminous flux can be defined as the radiated luminous power or power of
visible light expressed interms of its effect on the average or normal human eye.
7.Define luminance?
Luminance can be defined as the quantity of light intensity emitted per
square centimeter of an illuminated area.
8.What do you understand by illuminance?
Illuminance is the average luminous flux incident on to a surface.
9.what do you mean by resolving power or resolution?
It is the ability of the image reproducing system to represent the fine
structure of an object.
10.Mention some important characteristics of human eye?
Visual acuity, persistence of vision, brightness and colour sensation are
some of the important characteristics of human eye.
11.What are rods and cones?
The retina of the human eye consists of light sensitive cellular structures
of two kinds namely rods and cones. The rods sense primarily the brightness
levels including very faint impressions. The cones are mainly responsible for
colour perception. There are 65 lakhs cones and about 10 crores rods connected
to the brain through 8 lakhs optic nerve fibres.
12.Give the relationship between eye parameters?
The eye parameters are related by the following equation:
B=constant / c2a0
2
Where,
c- the constant ratio
b-the scene brightness
a0 - the minimum resolvable angle
13.Why is scanning necessary in television system?
Scanning is the important process carried out in a television system inorder
to obtain continuous frames and provides motion of picture. The scene is scanned
both in the horizontal and vertical directions simultaneously in a rabid rate. As a
result sufficient number of complete picture of frames per second is obtained to
give the illusion of continuous motion.
14.What do you understand by flicker?
The result of 24 pictures per second in motion pictures and that of scanning
25 frames per second in television pictures is enough to make an illusion of
continuity. But, they are not rapid enough to permit the brightness of one picture
or frame to blend smoothly in the next through the time when the screen is
blanked between successive frames. This develops in a definite flicker of light that
is very irritating to the observer when the screen is made alternately bright and
dark.
15.How will you solve the flickering problem?
The flickering problem is solved in motion pictures by showing each
picture twice. Hence 48 views of the scene are shown per second although they
are still the same 24 pictures frames per second. As a result of the increased
blanking rate, flicker is removed. In TV, Interlaced scaning is used to avoid flicker
16.What do you mean by interlaced scanning?
When the scanning beam reaches the bottom of the picture frame, it
quickly returns to the top to scan those lines that were missed in the previous
scanning. Hence the total number of lines are divided into two groups called
fields. Each field is scanned alternately. This way of scanning is called interlaced
scanning.
17.Define vertical resolution?
The capability of resolving picture details in the vertical direction is called
vertical resolution.
18.What is horizontal resolution?
The ability of the system to resolve maximum number of picture elements
along the scanning lines determines horizontal resolution.
19.List the contents of a composite video signal?
Composite video signal consists of a camera signal, blanking pulses and
synchronizing pulses.
20.What do you mean by pedestal?
The difference between the black level and blanking level is known as the
pedestal.
21.Define peak-white level?
The peak-white level is defined as the level of the video signal when the
picture detail being transmitted corresponds to the maximum whiteness to be
handled
22.Define pedestal height?
Pedestal height is the distance between the pedestal level and the average
value axis of the video signal.
23.What is the main function of the blanking pulses?
The composite video signal consist of blanking pulses to make the retrace
lines invisible by increasing the signal amplitude little above the black level of
75percent during the time scanning the circuits develop retrace.
24.What are per the post equalizing pulses?
To rectify the drawback which occurs on account of half-line discrepancy
five narrow pulses are added on either side of the vertical sync pulse. These are
called pre-equalising and post-equalising pulses .
25. Differentiate monochrome and colour camera tube.
In black and white camera only one pickup tube is needed but three such tubes or
its equivalent is necessary in color cameras to develop separate signals for red ,green and
blue information present in the scene.
26. Why do we prefer horizontal polarization for television receiving antenna?
We prefer horizontal polarization for television receiver antenna because it
results in more signal strength, less reflection and reduced ghost images.
27.Where can you employ indoor receiver antennas?
In strong signal areas it is sometimes feasible to use indoor antennas
provided the receiver is sufficiently sensitive.
28.A yagi antenna with a large number of directors is commonly used with
success in fringe areas for stations in the vhf band.
29.What do you understand by diplexer?
The outputs of both the video and the audio transmitter are
combined by the diplexer circuit and given to a common broadcast
transmitting antenna.
30. If two stations are operating at the same carrier frequency and located
nearby then they will interface with each other. This is called co-cannel
interference and it is common in fringe areas.
31 It is the interference due to stations located nearby and allocated as
adjacent channels.
32.Define guard band?
Guard band can be defined as a small frequency band introduced
between two consecutive channels inorder to reduce interference .
33. Ghost interference arises as a result of discrete reflections of the signal
from the surface of hills, bridges, buildings, towers etc.
34.Mention the requirements of high level modulation?
In high level modulation, the video signal has to be modulated by
the picture carrier in the final power amplifier which has a high power
level. Grid bias modulation is employed.
35.What do you understand by ground waves?
Vertically polarized electromagnetic waves are radiated at zero or
small angles with ground. They are guided by the conducting surface of
the ground along which they are propagated. Such waves are known as
ground or surface waves. As the ground waves travel along the surface of
the earth, their attenuation is proportional to frequency. The attenuation is
reasonably low below 1500KHz.Therefore, all medium wave broadcast and long
wave telegraph and telephone communication is carried out by ground wave
propagation.
36.What are sky waves?
In ground wave propagation ,frequencies above 1600 KHz does not serve
any useful purpose as the signal gets very much attenuated within a short distance
of its transmission .Therefore ,most radio communication in short wave bands
upto 30MHz is carried out by sky waves.When these waves are transmitted high
up in the sky , they travel in the straight line until the ionosphere is reached. This
region begins about 120Km above the surface of the earth. The region consists of
large concentrations of charge gaseous ions, free electrons and neutral molecules.
The ions and free electrons cause to band all passing electromagnetic waves.
37.Describe briefly about space wave propagation.
Propagation of radio waves above about 40MHz is not possible through
either sky wave or surface wave propagation .Therefore ,the only alternative for
transmission in the VHF and UHF bands, despite large attenuation is by radio
waves which travel in a straight line from transmitter to receiver. This called
space wave propagation.
38.Why is AM preferred over FM broadcasting the picture signal?
If FM is adopted for picture transmission ,the changing beat frequency
between the multiple paths delayed with respect to each other would develop a
bar interference in the image with a shimmering effect as the bars continuously
changes as the beat frequency changes therefore ,no study picture is
produced.Apart from that ,circuit complexity and BW requirements are much less
in AM than FM.Hence AM is preferred to FM for broadcasting the picture signal.
39.What is Dipole array?
Dipole antenna is used for band I&III transmitters. It consists of diploe
pnels mounted on the four sides at the top of the antenna tower.Each panel has an
array of full wave dipoles mounted in front of reflectors. To get an unidirectional
pattern ,the four panels mounted on the four sides of the tower are so fed that the
current in each lags behind the previous by 90 degree . This is done by changing
the field cable length by l/4 to the two alternate panels and by reversal of polarity
of the current.
40. Define Image rejection ratio.
Image rejection ratio is defined as the output due to desired station divided
by output due to image signal.
41. What do you refer by Yagi uda Antenna?
This is a widely used antenna for television receivers .Generally ,for
locations within 40 to 60Km from the transmitter is the folded dipole with one
reflector and one director. This is commonly called Yagi antenna or Yagi-Uda
antenna.
42. Name the essential parts of TV transmitter.
The essential parts of TV tranmitter includes a video processing unit . A
visual modulator which is a diode bridge modulator, phase compensator or delay
equalizer and frequency converter.
43. What is the main purpose of using VHF tuner?
The purpose tuner unit is to amplify both picture and sound signals picked
up the antenna and to convert the carrier frequencies and their associated side
bands into intermediate frequencies.
44. Name the essential components of RF section.
RF tuner section consists of RF amplifier ,mixer and local oscillator and is
normally mounted on a separate subchasis,called the front end.
45. What are the major tasks to be done by detector?
The video detector is designed to recover composite video signal and to
transform the sound signal to another lower carrier frequency.
46. Why is video amplifier required?
The amplitude of the composite video signal at the output of video
detector is not enough to drive the picture tube directly . Therefore further
amplification is required. This is done by video amplifier.
47. What are Sync pulses?
The Synchronizing pulses called ‘Sync’ are part of the composite video
signal as the top 25% of the signal amplitude. The sync pulses include horizontal
,vertical and equalizing pulses. Sync separator separates these signals from the
video signal.
48. Define frequency Distortion.
The inequality in gain at different frequency components of the received
signal is called frequency distortion.
49. List out the advantages of IF sections.
The main function of this section is to amplify modulated IF signal over
its entire bandwidth with an input of about 0.5mV signal from the mixer to deliver
about 4V into the video detector.
IF section is used to equalize amplitudes of sideband components ,because of
vestigial side band transmission.
IF section is used to reject the signals from adjacent channels.
50. What is meant by high level modulation.
In high level modulation modulation occurs in the output circuit of the
final amplifier.
11. What do you understand by Hue?
Hue or tint can be defined as the predominant spectral colour of the received light.
The colour of any object is distinguished by its hue or tint.
12. Define Brightness.
Brightness can be defined as theamount of light intensity as perceived by
the eye regardless of the colour.
13. What do you mean by saturation?
Saturation refers to the spectral purity of the colour light.It indicates the degree by
which the colour is diluted by white.
14. List any three requirements to be satisfied for compatibility in television systems.
a. It should has the same bandwidth as the corresponding monochrome
signal.
b. The colour signal should have the same brightness information as that of
monochrome signal.
c. The location and spacing of the picture and sound carrier frequencies
should remain the same.
15. What is additive mixing?
All light sensations to the eye are splitted in to three main colour groups
namely red,blue and green. The optic nerve system integratesthe different colour
impressions in accordance with the curve to perceive the actual colour of the
object.
16. State grassman’s law.
The brightness impression produced by the three primaries that constitute
the single light. This property of the eye of generating a response which depends
on the algebraic sum of the blue ,red and green inputs is called grassman’s law.
17. Explain the significance of generating colour difference signals.
Colour difference signals are generated to avoid the separate transmission
of R,G,B signals.
18. Why is (G-y) not suitable for transmission?
The proportion of G is large in luminance signal,hence magnitude of (GY)
is relatively small so it requires amplifiers at the receiving end.
It affect the signal to noise ratio at the transmitting end.
19. What is gamma correction.
A colour camera is used develop three voltages proportional to red,green and blue
colour contents of the picture.These voltages are represented as R,G,B.a
correction is applied to these voltages to compensate for any nonlinearity of the
system and that is the swinging burst.this is known as swinging burst.
23. Merits of SECAM system.
SECAM system has several advantages because of frequency modulation
of the subcarrier and transmission of one line at a time.
SECAM receivers are immune to phase distortion.
Both the luminance and chrominance signals are not present at the same
time ,there is no possibility of cross talk between the colour difference
signals.
Ther is no need for the use of QAM at the transmitter and synchronous
detectors at the receiver.
The receiver does not need Automatic tuning control and Automatic color
control
24. Demerits of SECAM system.
In SECAM system luminance is represented by the amplitude of voltage
but hue and saturation are represented by deviation of the subcarrier.when a
composite signal involving luminance and chrominance is faded out in studio
operation,it is the luminance signal that is readily attenuated and not6 the
chrominance.This makes the color more saturated during fade to black.
25. Limitations of the NTSC system.
The NTSC system is sensitive to transmission path differences which
introduces phase errors that result in colour changes in the picture. At the
transmitter,phase changes in the chroma signal take place when change over
between programmes of local and television network systems takes place and
when video tape recorders are switched on .The phase angle is also affected by
the level of the signal while passing through various circuits .In addition cross talk
between demodulator outputs at the receiver causes colour distortion.
26. Mention some features of PAL system.
a. The weighted (B-Y) and (R-Y) signals are modulated without being given
a phase shift of 33 as is done in the NTSC system.
b. On modulation both the color difference signals are allowed the same
bandwidth of about 1.3MHz.
c. The color subcarrier frequency is chosen to be 4.43MHz.
d. The weighted color difference signals are quadrature modulated with the
subcarrier.
27. Write notes on NTSC system.
NTSC system is compatible with 525 line American system.In order to
maintain compatibility two new colour difference signals are generated and they
are represented as I and Q. Since eye is capable of resolving finer details in the
regions around I,it is allowed to have a maximum bandwidth of 1.5MHz.The
bandwidth of Q signal is restricted to 0.5MHz.
28. What is the difference between NTSC,PAL and SECAM?
The difference between the SECAM system on one hand and NTSC and
PAL on the other is that the later transmit and receive two chrominance signals
simultaneously while in the SECAM system only one of the two color difference
signal is transmitted at a time.
29. What do you mean by high frequency preemphasis?
In SECAM system, the chrominance signals are pre-emphasized before
modulation. After modulating the carrier with the pre-emphasized and weighted
color difference signals, another form of preemphasis is carried out on the signals.
This takes the form of increasing amplitude of the sub carrier as its deviation
increases. Such a preemphasis is called high frequency preemphasis.
30. What is the use of line identification pulses?
In SECAM system ,the switching of Dr and Db signals line by line takes
place during the line sync pulse period.The sequence of switching continues
without interruption from one field to the next and is maintained through the field
blanking interval.However it is necessary for the receiver to be able to deduce as
to which line is being transmitted.Such an identification of the proper sequence of
color lines in each field is accomplished by identification pulses.
71. Write notes on luminance channel.
The video amplifier in the luminance channel is Dc coupled and has the same
bandwidth as in the monochrome receiver. It is followed by a delay line to
compensate for the additional delay the color signal suffers because of limited
bandpass of the chrominance amplifier .This ensures time coincidence of the
luminance and chrominance signals. The channel also includes a notch filter
which attenuates the subcarrier by about 10db.This helps to suppress the
appearance of any dot structure on the screen along with the color picture.
72. What is the use of chrominance bandpass amplifier?
The chroma bandpass amplifier selects the chrominance signal and rejects
other unwanted components of the composite signal.
73. What do you mean by automatic color control?
The ACC circuit is similar to the AGC circuit used for automatic gain
control of RF and IF stages of the receiver.It develops a dc control voltage that is
proportional to the amplitude of the color burst.
74. Write short notes on color killer circuit.
When a monochrome transmission is received there is no input to the color
killer and no positive voltage is developed . Therefore no input is given to the
second chroma amplifier from the color killer circuit ,it blocks the second chroma
amplifier.Thus it prevents the color noise on black and white picture.
75. Merits of PAL system.
The problem of differential phase errors has been successfully overcome
in the PAL system.
76. Demerits of PAL system.
The use of phase alteration by line technique and associated control circuitry
together with the need of a delay line in the receiver makes the PAL system more
complicated and expensive.The receiver cost is higher for the PAL colour system.
77. What do you mean by automatic frequency tuning?
AFT is used to improve the stability of the oscillator circuit ,some drift does occur
on account of ambient temperature changes ,component aging ,power supply
voltage fluctuation and so on. The fine tuning control is adjusted to get a sharp
picture.
78. Write short notes on burst seperator.
The burst seperator circuit has the function of extracting 8 to 10 cycles of
reference color burst which are transmitted on the back porch of every horizontal
pulse .the circuit is tuned to the subcarrier frequency and is keyed on during the
flyback time by pulses derived from the horizontal output stage.
79. What is the use of color subcarrier oscillator?
The function of subcarrier oscillator is to generate a carrier wave output at
3.57MHz and feed it to the demodulators.The subcarrier frequency is maintained
at its correct value and phase by the APC circuit.
80. How the phase error is cancelled in the PAL system.
In PAL system phase shift error is cancelled by reversing the phase angle
of v signal on alternate lines.
81. Give the abbreviation for NTSC, SECAM ,and PAL.
NTSC -National Television systems committee
SECAM –Sequential –a-Memoire
PAL - Phase Alteration by Line
82. What do you understand by PAL –D Colour system.
The use of eye as the averaging mechanism for the correct hue is the basic
concept of simple ‘PAL’ system. Beyond a certain limit , the human eye see the
effect of colour changes on alternate lines hence the system needs modification.
Considerable improvement found in the system of a delay line is used to do the
averaging first and then present the color to the eye.This is called PAL-D or delay
line PAL method and is most commonly employe in PAL receivers.
83. Write short notes on colour subcarrier frequency of PAL D system.
The color sub carrier frequency of 4.43MHz is produced with a crystal controlled
oscillator .To accomplish minimum raster disturbance through the color
subcarrier it is important to maintain correct frequency relationship between the
scanning frequencies and subcarrier frequency .Therefore ,it is usual to count
down from the subcarrier frequency to twice the line frequency pulses .
84. write short notes on AGC circuit.
AGC circuit is used to control the gain of RF and IF amplifiers .The change in
gain is achieved by shifting the operating point of transistors used in the
amplifiers.The operating point is changed by a bias voltage that is developed in
the AGC circuit.
85. What do you mean by Peak AGC system?
The system based on sampling the sync tip levels is known as “peak”
AGC system.The Peak AGC system is also called as non-keyed AGC sytem.
86. What are the two types of AGC control?
Forward AGC control
Reverse AGC control
87. What is Forward AGC control?
In any transistor amplifier ,gain is varied by shifting the operating point either
towards collector current cutoff or saturation. This actually varies beta of the
transistor and hence the stage gain changes.When gain is changed by shifting the
operating point towards current cutoff ,then it is called “Reverse AGC”.
88. What is forward AGC?
In any transistor amplifier ,gain is varied by shifting the operating point either
towards collector current cutoff or saturation. This actually varies beta of the
transistor and hence the stage gain changes.When gain is changed by shifting the
operating point towards collector current saturation ,then it is called “Forward
AGC”.
89. List the draw backs of nonkeyed AGC.
The AGC voltage developed across the peak rectifier load tends to increase during
vertical sync pulse periods because the video signal amplitude remains almost at the
peak value every time vertical sync pulses occur. This results in a 50Hz ripple over
the negative AGC voltage and reduces gain of the receiver during these intervals.The
reduced gain results in weak vertical sync pulse which in turn can put the vertical
deflection oscillator out of synchronism causing rolling of the picture.
90. Merits of Keyed AGC system.
AGC voltage developed is a true representation of the peak of fixedsync
level and thus corresponds to the actual incoming signal strength.
Noise effects are minimized because conduction is restricted to a small
fraction of the total line period.
91. Write short notes on CATV.
CATV stands for community antenna television systems. The CATV
system is a cable system distributes good quality television signal to a very large
number of receivers throughout an entire community. Generally this system gives
increased TV programmes to subscribers who pay a fee for this service. A cable
system may have many more active VHF and UHF channels than a receiver tuner
can directly select.
.
92. What do you understand by satellite TV?
Satellite TV is a TV from space. Broadcasters from earth transmit their
programmes to specified satellites. Then, the transmissions are returned to
receiving equipment on the ground. Therefore, the better the receiving equipment
,the higher the quality of the reception.
93. List some of the applications of satellite TV?
The shear range of programmes currently available on satellite channel is
very much impressive such as 24-hour music videos, news, and feature films. A
variety of general entertainment programmes, sports ,children’s programmes ,
foreign language broadcasts and cultural programmes are all available for the
keyboard dish owner. Some of these come through subscription channels and
others by free to watch channels which are sponsored by advertising.
94. State the merits of satellite TV.
The picture quality from satellite systems is surprisingly good and
compares well with conventional land based TV transmissions. In addition unlike
terrestrial broadcasts it is free from the spectrum of picture ghosting.
95. Mention the limitations of satellite TV.
The limitation of the satellite TV is varying picture and audio quality .By
adopting de-emphasis circuits we can avoid the variations.
96. Give the applications of video tape recorders.
Smaller and lower priced video tape recorders using ½ inch tape are
available for closed type circuit TV or for use in the home. They can record and
playback programs on a television receiver in color and monochrome. In addition
to that small portable cameras are provided for a complete television system with
the recorder. These portable systems are also employed for taping television
programs from a remote are also employed for taping television programs from a
remote location for away from the TV broadcast studio.
97. List some merits of high definition television.
Improvement in both vertical and horizontal resolution of the reproduced
picyure by approximately 2:1 over existing standards.
Much improved colour rendition
Higher aspect ratio of atleast 5:3
Stereophonic sound
98. What do you mean by Longitudinal video recording?
A method in which video signals are recorded on atleast several tracks
along the length of the tape.
99. What do you mean by Quadruplex (Transverse) scan recording?
In transverse scan recording ,four recording heads are spaced 90 apart and
are mounted on a rotating drum and the tape moves past it,transversely.Each head
comes in contact with the tape as the previous one leaves it.
100. What do you mean by helical scan recording ?
In helical scan recording ,the two recording heads ‘look at ‘ the tape
surface as it is drawn past them through two tiny rectangular slits mounted on
opposite sides of the drum.The heads thus trace out diagonal tracks across the
tape,one track per head.
101. What are two types of video disc system?
Laser or optical disc system
Capacitance disc system
102. List the fundamental components of DVD player.
A drive motor to spin the disc.
A laser and lens system to focus in on the bumps and read them.
Tracking mechanism that can move the laser assembly so that the lasers
beam can follow the spiral track.
Electronic circuitry
103. What are the advantages of DVD players over VCR’s.
The quality of picture and sound in a DVD is better than on a video
tape,and DVD’s maintain their high quality over time,because there is no
physical contact with the disc as it revolves.
104. List 4 merits of digital TV receivers.
o Reduced Ghosts
o Reduction of 50Hz flicker
o High resolution pictures
o Slow motion action
PART that faces the gun.
• Number of electrons from the beam is then deposited on the photo layer
surface to reduce to reduce the potential of each element.
• Sudden change in potential on each element causes a current flow in the
signal electrode circuit producing a varying voltage across the load
resistance.
3. Give the constructional details of a monochrome picture tube and explain the
beam landing
Employs electrostatic focusing and electro magnetic deflection
Composite video signal that is injected either at the grid or cathode of the
tube
Electron Gun:-emits the electron beam with proper energy to cause it to fluoresce,
another anode called final anode is included within the tube.
Low Voltage Focusing:
It needs less voltage at the focusing electrodes.
High Voltage Focusing:
It requires high voltage at the focusing electrode. This focus system is
called ‘unipotential lens’ system.
Picture Tube Screen:
Screen phosphor: -light metals such as zinc and cadmium in the form of
sulphide, sulphate, and phosphor compounds are used.
Screen Brightness:-picture tubes employ a very thin coating of aluminium
on the back surface of the screen .This improves the screen brightness.
4. Explain in detail the silicon diode array vidicon camera tube.
It uses photovoltaic type where the target is prepared from a thin n-type silicon
wafer instead of deposited layers on the glass faceplate.
Oxidation:-to form a film of silicon dioxide(Sio2)which is an insulator.
Photomasking and etching: - an array of fine openings is made in the
Oxide layer.
Boron is vapourized through the array of holes.
Thin layer of gold is deposited on each p type opening to form contacts for
signal output.

The silicon target plate thus formed is typically 0.003cm thick,1.5 cm
square having an array of 540x540 photodiodes.
The Target plate is mounted in a vidicon type of camera tube.
5. Write notes on composite video signal.
Composite video signal consists of a camera signal, blanking pulses
and synchronizing pulses.
The difference between the black level and blanking level is known
as the pedestal.
The peak-white level is defined as the level of the video signal
when the picture detail being transmitted corresponds to the
maximum whiteness to be handled
Pedestal height is the distance between the pedestal level and the
average value axis of the video signal.
The composite video signal consist of blanking pulses to make the
retrace lines invisible by increasing the signal amplitude little above
the black level of 75percent during the time scanning the circuits
develop retrace.
To rectify the drawback which occurs on account of half-line
discrepancy five narrow pulses are added on either side of the
vertical sync pulse. These are called pre-equalising and postequalising
pulses .
6. Draw Block Diagram of RF Tuner and explain how incoming signals from
different sections are translated to common picture IF and sound IF frequencies.
RF tuner section consists of RF amplifier ,mixer and local oscillator and is
normally mounted on a separate subchasis,called the front end.
The purpose tuner unit is to amplify both picture and sound signals picked
up the antenna and to convert the carrier frequencies and their associated
side bands into intermediate frequencies.
The receiver uses superheterodyne principle.The signal voltage or
information from various stations modulated over different carrier
frequencies is heterodyned in the mixer with the output from a local
oscillator to transfer original information on a common fixed carrier
frequency called intermediate frequency(IF)
The setting of local oscillator frequency enables selection of desired
station.
7. Describe briefly the factors that influenced the choice of picture IF =38.9 and
sound IF =33.4MHz in the 625 line system.
The factors that influence the choice of intermediate frequencies in TV receivers
are:
Image Rejection Ratio:
Image rejection ratio is defined as the output due to desired station
divided by output due to image signal.
Pickup due to local oscillator radiation from TV receivers
Image Frequencies should not lie in the FM band
Interference or direct pickup from bands assigned for other services
Gain
8. Explain how composite video signal is detected ?How is the polarity of video
output signal decided?
Modulated IF signals after due amplification in the IF section are fed to
the video detector .
The video detector is designed to recover composite video signal and to
transform the sound signal to another lower carrier frequency.
This is done by rectifying the input signal and filtering out unwanted
frequency components.
A diode is used ,which is suitably polarized to rectify either positive or
negative peaks of the input signal.
9. Draw block diagram of a monochrome TV receiver and briefly explain the
operation of TV receiver.
A black and white receiver has six main sections:-
Tuner section, IF sub system ,Video section ,Audio section, Deflection and power
supply.
Tuner section:
This section consists of RF amplifier ,mixer and local oscillator.It selects the
desired channel signal from those picked up by the antenna and converts it into
the IF band.
IF subsystem:
The IF subsystem includes IF section ,AGC circuit and video detector.The IF
section provides large amplification to the weak IF signals and the video detector
that follows IF amplifiers produces composite video and intercarrier FM sound
signals.
Video section:
The Video signal is accorded large amplification and fed to the picture tube.
Audio section:
The sound associated with the picture is transmitted as an FM signal with a center
frequency 5.5MHz above the station picture carrier frequency. The sound signal
BW is only about 150Khz as compared to the large bandwidth of 5MHz for the
picture signal.
Sync separation and processing:
The horizontal and vertical sync pulses that form part of the composite video
signal are separated in the sync separator. The composite video signal is either
taken from the video detector output or after one stage of video amplification.
DC power supplies:
All the active devices ,ICs and picture tube need a dc source for their operation.
Rectifiers are used to convert ac to dc and filters provided to eliminate ac ripple in
the dc output.
10. Explain briefly the operation of IF subsystem.
The IF subsystem includes IF section ,AGC circuit and video
detector.The IF section provides large amplification to the weak IF signals and the
video detector that follows IF amplifiers produces composite video and
intercarrier FM sound signals.
The factors that influence the choice of intermediate frequencies in TV receivers
are:
Image Rejection Ratio:
Image rejection ratio is defined as the output due to desired station
divided by output due to image signal.
Pickup due to local oscillator radiation from TV receivers
Image Frequencies should not lie in the FM band
Interference or direct pickup from bands assigned for other services
Gain
IF section :
The main function of this section is to amplify modulated IF signal over
its bandwidth with an input of about 0.5mV signal from the mixer to
deliver about 4V into the video detector.
IF section is used to equalize amplitudes of sideband components ,because
of vestigial side band transmission.
IF section is used to reject the signals from adjacent channels.
11. Explain in detail the NTSC color receiver system.
NTSC system is compatible with 525 line American system.In order to
maintain compatibility two new colour difference signals are generated and they
are represented as I and Q. Since eye is capable of resolving finer details in the
regions around I,it is allowed to have a maximum bandwidth of 1.5MHz.The
bandwidth of Q signal is restricted to 0.5MHz.
Limitations of the NTSC system.
The NTSC system is sensitive to transmission path differences which introduces
phase errors that result in colour changes in the picture. At the transmitter,phase
changes in the chroma signal take place when change over between programmes
of local and television network systems takes place and when video tape recorders
are switched on .The phase angle is also affected by the level of the signal while
passing through various circuits .In addition cross talk between demodulator
outputs at the receiver causes colour distortion.
12. Explain working of a pAL system.
The weighted (B-Y) and (R-Y) signals are modulated without being given
a phase shift of 33 as is done in the NTSC system.
On modulation both the color difference signals are allowed the same
bandwidth of about 1.3MHz.
The color subcarrier frequency is chosen to be 4.43MHz.
The weighted color difference signals are quadrature modulated with the
subcarrier.
13.Describe with necessary diagrams the encoding of color difference signal.
Quadrature modulation:
It is used to combine two colour difference signals in to a single variable.
Frequency interleaving:
The technique of combining two distinct signal within the same bandwidth
is known as frequency interleaving.
Colour burst:
Sample of colour subcarrier output at the encoder are transmitted along
with other sync pulses.
14.Describe the generation of Y signal and color difference signals.
Find the value for cyan.
In a color camera ,the luminance or Y signal is obtained by adding R,G
and B in the following proportions
Y=0.30R+0.59G+0.11B.
15.Explain in detail about SECAM system.
SECAM color system is compatible wit819 line monochrome system.
The difference between the SECAM system on one hand and NTSC and
PAL on the other is that the later transmit and receive two chrominance signals
simultaneously while in the SECAM system only one of the two color difference
signal is transmitted at a time.
In SECAM system, the chrominance signals are pre-emphasized
before modulation. After modulating the carrier with the pre-emphasized and
weighted color difference signals, another form of preemphasis is carried out on
the signals. This takes the form of increasing amplitude of the sub carrier as its
deviation increases. Such a preemphasis is called high frequency preemphasis.
16.Explain the working of U and V demodulators.
The chrominance available at the output of delay line circuitry consists of
two suppressed carrier amplitude modulated components designated as U
and V.
These correspond to the two color difference signal and bear information
about their amplitude and polarity
Because of quadrature modulation ,the two modulation product signals
have a phase difference of 90 at any instant with respect to each other.
Thus when one is passing through its positive or negative peak, the other
is passing through Zero.
The demodulating devices are normally biased to cutoff and conduct only
at positive peaks of the externally fed subcarrier which is large in
amplitude.
17.Describe with a circuit Burst phase discriminator.
The burst seperator circuit has the function of extracting 8 to 10 cycles of
reference color burst which are transmitted on the back porch of every horizontal
pulse. The circuit is tuned to the subcarrier frequency and is keyed on during the
flyback time by pulses derived from the horizontal output stage.
18.Write the need and working of Automatic Gain control Circuit.
AGC circuit controls the gain of RF and IF stage to enable almost constant
signal voltage at the output of video detector, despite changes in the signal picked
up by the antenna. The change in gain is achieved by shifting the operating point
of transistors used in the amplifiers. The operating point is changed by a bias
voltage that is developed in the bias circuit.
19.Write Short notes on color killer circuit.
When a monochrome transmission is received there is no input to the color
killer and no positive voltage is developed . Therefore no input is given to the
second chroma amplifier from the color killer circuit ,it blocks the second chroma
amplifier.Thus it prevents the color noise on black and white picture.
20.Briefly explain PAL-D system.
The use of eye as the averaging mechanism for the correct hue is the basic
concept of simple ‘PAL’ system. Beyond a certain limit , the human eye see the
effect of colour changes on alternate lines hence the system needs modification.
Considerable improvement found in the system of a delay line is used to do the
averaging first and then present the color to the eye.This is called PAL-D or delay
line PAL method and is most commonly employe in PAL receivers.
21.Briefly explain satellite based TV broadcast system.
Satellite TV is a TV from space. Broadcasters from earth transmit their
programmes to specified satellites. Then, the transmissions are returned to
receiving equipment on the ground. Therefore, the better the receiving equipment
,the higher the quality of the reception.
Applications of satellite TV:
The shear range of programmes currently available on satellite channel is
very much impressive such as 24-hour music videos, news, and feature films. A
variety of general entertainment programmes, sports ,children’s programmes ,
foreign language broadcasts and cultural programmes are all available for the
keyboard dish owner. Some of these come through subscription channels and
others by free to watch channels which are sponsored by advertising.
Limitation:
The limitation of the satellite TV is varying picture and audio quality .By
adopting de-emphasis circuits we can avoid the variations.
22.Write short notes on Video disc system.
The video disc is essentially a gramophone record with pictures on it.The
first video disc was the laser optical and the second video disc system is based on
t UNIVERSITY RE-EVALUATION RESULTS