NOORUL ISLAM COLLEGE OF ENGINEERING, KUMARACOIL
DEPARTMENT OF ECE
EC 1401 – VLSI DESIGN
TWO MARK & BIG QUESTIONS WITH ANSWERS
COMPILED BY
V.S.DHARUN
LECTURER,ECE
2 MARK QUESTIONS & ANSWERS
1.What are four generations of Integration Circuits?
SSI (Small Scale Integration)
MSI (Medium Scale Integration)
LSI (Large Scale Integration)
VLSI (Very Large Scale Integration)
2.Give the advantages of IC?
Size is less
High Speed
Less Power Dissipation
3.Give the variety of Integrated Circuits?
More Specialized Circuits
Application Specific Integrated Circuits(ASICs)
Systems-On-Chips
4.Give the basic process for IC fabrication
Silicon wafer Preparation
Epitaxial Growth
Oxidation
Photolithography
Diffusion
Ion Implantation
Isolation technique
Metallization
Assembly processing & Packaging
5.What are the various Silicon wafer Preparation?
Crystal growth & doping
Ingot trimming & grinding
Ingot slicing
Wafer polishing & etching
Wafer cleaning.
6.Different types of oxidation?
Dry & Wet Oxidation
7.What is the transistors CMOS technology provides?
n-type transistors & p-type transistors.
8.What are the different layers in MOS transistors?
Drain , Source & Gate
9.What is Enhancement mode transistor?
The device that is normally cut-off with zero gate bias.
10. What is Depletion mode Device?
The Device that conduct with zero gate bias.
11.When the channel is said to be pinched –off?
If a large Vds is applied this voltage with deplete the Inversion layer .This Voltage
effectively pinches off the channel near the drain.
12.Give the different types of CMOS process?
p-well process
n-well process
Silicon-On-Insulator Process
Twin- tub Process
13.What are the steps involved in twin-tub process?
Tub Formation
Thin-oxide Construction
Source & Drain Implantation
Contact cut definition
Metallization.
14.What are the advantages of Silicon-on-Insulator process?
No Latch-up
Due to absence of bulks transistor structures are denser than bulk silicon.
15.What is BiCMOS Technology?
It is the combination of Bipolar technology & CMOS technology.
16.What are the basic processing steps involved in BiCMOS process?
Additional masks defining P base region
N Collector area
Buried Sub collector (SCCD)
Processing steps in CMOS process
17.What are the advantages of CMOS process?
Low power Dissipation
High Packing density
Bi directional capability
18.What are the advantages of CMOS process?
Low Input Impedance
Low delay Sensitivity to load.
19.What is the fundamental goal in Device modeling?
To obtain the functional relationship among the terminal electrical variables of the
device that is to be modeled.
20.Define Short Channel devices?
Transistors with Channel length less than 3- 5 microns are termed as Short channel
devices. With short channel devices the ratio between the lateral & vertical dimensions
are reduced.
21.What is pull down device?
A device connected so as to pull the output voltage to the lower supply voltage usually
0V is called pull down device.
22.Whateas.
29. Compare between CMOS and bipolar technologies.
CMOS Technology Bipolar technology
• Low static power dissipation
• High input impedance (low drive
current)
• Scalable threshold voltage
• High noise margin
• High packing density
• High delay sensitivity to load (fanout
limitations)
• Low output drive current
• Low gm (gm a Vin)
• Bidirectional capability
• A near ideal switching device
• High power dissipation
• Low input impedance (high drive
current)
• Low voltage swing logic
• Low packing density
• Low delay sensitivity to load
• High output drive current
• High gm (gm a eVin)
• High ft at low current
• Essentially unidirectional
30.Define Threshold voltage in CMOS?
The Threshold voltage, VT for a MOS transistor can be defined as the voltage applied
between the gate and the source of the MOS transistor below which the drain to
source current, IDS effectively drops to zero.
31.What is Body effect?
The threshold volatge VT is not a constant w. r. to the voltage difference between the
substrate and the source of MOS transistor. This effect is called substrate-bias effect or
body effect.
32.What is Channel-length modulation?
The current between drain and source terminals is constant and independent of the
applied voltage over the terminals. This is not entirely correct. The effective length of the
conductive channel is actually modulated by the applied VDS, increasing VDS causes the
depletion region at the drain junction to grow, reducing the length of the effective
channel.
33. What is Latch – up?
Latch up is a condition in which the parasitic components give rise to the establishment
of low resistance conducting paths between VDD and VSS with disastrous results. Careful
control during fabrication is necessary to avoid this problem.
34. Give the basic inverter circuit.
35. Give the CMOS inverter DC transfer characteristics and operating regions
36.Define Rise time
Rise time, tr is the time taken for a waveform to rise from 10% to 90% of its steady-state
value.
37. Define Fall time
Fall time, tf is the time taken for a waveform to fall from 90% to 10% of its steady-state
value.
38. Define Delay time
Delay time, td is the time difference between input transition (50%) and the 50% output
level. This is the time taken for a logic transition to pass from input to output.
39. What are two components of Power dissipation.
There are two components that establish the amount of power dissipated in a
CMOS circuit. These are:
i) Static dissipation due to leakage current or other current drawn
continuously from the power supply.
ii) Dynamic dissipation due to
- Switching transient current
- Charging and discharging of load capacitances.
40. Give some of the important CAD tools.
Some of the important CAD tools are:
i) Layout editors
ii) Design Rule checkers (DRC)
iii) Circuit extraction
41.What is Verilog?
Verilog is a general purpose hardware descriptor language. It is similar in syntax
to the C programming language. It can be used to model a digital system at many
levels of abstraction ranging from the algorithmic level to the switch level.
42. What are the various modeling used in Verilog?
1. Gate-level modeling
2. Data-flow modeling
3. Switch-level modeling
4. Behavioral modeling
43. What is the structural gate-level modeling?
Structural modeling describes a digital logic networks in terms of the components
that make up the system. Gate-level modeling is based on using primitive logic
gates and specifying how they are wired together.
44.What is Switch-level modeling?
Verilog allows switch-level modeling that is based on the behavior of MOSFETs.
Digital circuits at the MOS-transistor level are described using the MOSFET
switches.
45. What are identifiers?
Identifiers are names of modules, variables and other objects that we can
reference in the design. Identifiers consists of upper and lower case letters, digits
0 through 9, the underscore character(_) and the dollar sign($). It must be a single
group of characters.
Examples:
A014, a ,b, in_o, s_out
46. What are the value sets in Verilog?
Verilog supports four levels for the values needed to describe hardware referred to
as value sets.
Value levels
Condition in hardware circuits
0 Logic zero, false condition
1 Logic one, true condition
X Unknown logic value
Z High impedance, floating state
47. What are the types of gate arrays in ASIC?
1) Channeled gate arrays
2) Channel less gate arrays
3) Structured gate arrays
48. Give the classifications of timing control?
Methods of timing control:
1. Delay-based timing control
2. Event-based timing control
3. Level-sensitive timing control
Types of delay-based timing control:
1. Regular delay control
2. Intra-assignment delay control
3. Zero delay control
Types of event-based timing control:
1. Regular event control
2. Named event control
3. Event OR control
4. Level-sensitive timing control
49 Give the different arithmetic operators?
Operator symbol Operation performed Number of operands
* Multiply Two
/ Divide Two
+ Add Two
- Subtract Two
% Modulus Two
** Power (exponent) Two
50. Give the different bitwise operators.
Operator symbol Operation performed Number of operands
~ Bitwise negation One
& Bitwise and Two
| Bitwise or Two
^ Bitwise xor Two
^~ or ~^ Bitwise xnor Two
~& Bitwise nand Two
~| Bitwise nor Two
51. What are gate primitives?
Verilog supports basic logic gates as predefined primitives. Primitive logic
function keyword provide the basics for structural modeling at gate level. These
primitives are instantiated like modules except that they are predefined in verilog
and do not need a module definition. The important operations are and, nand, or,
xor, xnor, and buf(non-inverting drive buffer).
52. Give the two blocks in behavioral modeling.
1. An initial block executes once in the simulation and is used to set up
initial conditions and step-by-step data flow
2. An always block executes in a loop and repeats during the simulation.
53. What are the types of conditional statements?
1. No else statement
Syntax : if ( [expression] ) true – statement;
2. One else statement
Syntax : if ( [expression] ) true – statement;
else false-statement;
3. Nested if-else-if
Syntax : if ( [expression1] ) true statement 1;
else if ( [expression2] ) true-statement 2;
else if ( [expression3] ) true-statement 3;
else default-statement;
The [expression] is evaluated. If it is true (1 or a non-zero value) true-statement is
executed. If it is false (zero) or ambiguous (x), the false-statement is executed.
54. Name the types of ports in Verilog
Types of port Keyword
Input port Input
Output port Output
Bidirectional port inout
55. What are the types of procedural assignments?
1. Blocking assignment
2. Non-blocking assignment
56. Give the different symbols for transmission gate.
57. Give the different types of ASIC.
1. Full custom ASICs
2. Semi-custom ASICs
* standard cell based ASICs
* gate-array based ASICs
3. Programmable ASICs
* Programmable Logic Device (PLD)
* Field Programmable Gate Array (FPGA).
58. What is the full custom ASIC design?
In a full custom ASIC, an engineer designs some or all of the logic cells, circuits or
layout specifically for one ASIC. It makes sense to take this approach only if there
are no suitable existing cell libraries available that can be used for the entire design.
59. What is the standard cell-based ASIC design?
A cell-based ASIC (CBIC) USES PREDESIGNED LOGIC CELLS KNOWN AS
STANDARD CELLS. The standard cell areas also called fle4xible blocks in a CBIC
are built of rows of standard cells. The ASIC designer defines only the placement of
standard cells and the interconnect in a CBIC. All the mask layers of a CBIC are
customized and are unique to a particular customer.
60. Differentiate between channeled & channel less gate array.
Channeled Gate Array Channel less Gate Array
1. Only the interconnect is customized
Only the top few mask layers are
customized.
2. The interconnect uses predefined
spaces between rows of base cells.
No predefined areas are set aside for routing
between cells.
3. Routing is done using the spaces Routing is done using the area of transistors
unused.
4. Logic density is less Logic density is higher.
61. Give the constituent of I/O cell in 22V10.
2V10 I/O cell consists of
1. a register
2. an output 4:1 mux
3. a tristate buffer
4. a 2:1 input mux
It has the following characteristics:
* 12 inputs
* 10 I/Os
* product time 9 10 12 14 16 14 12 10 8
* 24 pins
62. What is a FPGA?
A field programmable gate array (FPGA) is a programmable logic device that
supports implementation of relatively large logic circuits. FPGAs can be used to
implement a logic circuit with more than 20,000 gates whereas a CPLD can implement
circuits of upto about 20,000 equivalent gates.
63. What are the different methods of programming of PALs?
The programming of PALs is done in three main ways:
• Fusible links
• UV – erasable EPROM
• EEPROM (E2PROM) – Electrically Erasable Programmable ROM
64.What is an antifuse?
An antifuse is normally high resistance (>100MW). On application of appropriate
programming voltages, the antifuse is changed permanently to a low-resistance
structure (200-500W).
65. What are the different levels of design abstraction at physical design.
• Architectural or functional level
• Register Transfer-level (RTL)
• Logic level
• Circuit level
66.What are macros?
The logic cells in a gate-array library are often called macros.
67. What are Programmable Interconnects ?
In a PAL, the device is programmed by changing the characteristics if the switching
element. An alternative would be to program the routing.
68. Give the steps inASIC design flow.
a. Design entry
b. Logic synthesisSystem partitioning
c. Prelayout simulation.
d. Floorplanning
e. Placement
f. Routing
g. Extraction
1. Postlayout simulation
69. Give the XILINX Configurable Logic Block .
70. Give the XILINX FPGA architecture
71. Mention the levels at which testing of a chip can be done?
a) At the wafer level
b) At the packaged-chip level
c) At the board level
d) At the system level
e) In the field
72.What are the categories of testing?
a) Functionality tests
b) Manufacturing tests
73. Write notes on functionality tests?
Functionality tests verify that the chip performs its intended function.
These tests assert that all the gates in the chip, acting in concert, achieve a desired
function. These tests are usually used early in the design cycle to verify the
functionality of the circuit.
74. Write notes on manufacturing tests?
Manufacturing tests verify that every gate and register in the chip
functions correctly. These tests are used after the chip is manufactured to verify
that the silicon is intact.
75. Mention the defects that occur in a chip?
a) layer-to-layer shorts
b) discontinous wires
c) thin-oxide shorts to substrate or well
76. Give some circuit maladies to overcome the defects?
a. nodes shorted to power or ground
b. nodes shorted to each other
c. inputs floating/outputs disconnected
77. What are the tests for I/O integrity?
a. I/O level test
b. Speed test
c. IDD test
78. What is meant by fault models?
Fault model is a model for how faults occur and their impact on circuits.
79. Give some examples of fault models?
a. Stuck-At Faults
b. Short-Circuit and Open-Circuit Faults
80. What is stuck – at fault?
With this model, a faulty gate input is modeled as a “stuck at zero” or
“stuck at one”. These faults most frequently occur due to thin-oxide shorts or
metal-to-metal shorts.
81. What is meant by observability?
The observability of a particular internal circuit node is the degree to
which one can observe that node at the outputs of an integrated circuit.
82. What is meant by controllability?
The controllability of an internal circuit node within a chip is a measure of
the ease of setting the node to a 1 or 0 state.
83. What is known as percentage-fault coverage?
The total number of nodes that, when set to 1 or 0, do result in the
detection of the fault, divided by the total number of nodes in the circuit, is called
the percentage-fault coverage.
84. What is fault grading?
Fault grading consists of two steps. First, the node to be faulted is selected.
A simulation is run with no faults inserted, and the results of this simulation are
saved. Each node or line to be faulted is set to 0 and then 1 and the test vector set
is applied. If and when a discrepancy is detected between the faulted circuit
response and the good circuit response, the fault is said to be detected and the
simulation is stopped.
85. Mention the ideas to increase the speed of fault simulation?
a. parallel simulation
b. concurrent simulation
86. What is fault sampling?
An approach to fault analysis is known as fault sampling. This is used in
circuits where it is impossible to fault every node in the circuit. Nodes are
randomly selected and faulted. The resulting fault detection rate may be
statistically inferred from the number of faults that are detected in the fault set and
the size of the set. The randomly selected faults are unbiased. It will determine
whether the fault coverage exceeds a desired level.
87. What are the approaches in design for testability?
a. ad hoc testing
b. scan-based approaches
c. self-test and built-in testing
88. Mention the common techniques involved in ad hoc testing?
a. partitioning large sequential circuits
b. adding test points
c. adding multiplexers
d. providing for easy state reset
89. What are the scan-based test techniques?
a) Level sensitive scan design
b) Serial scan
c) Partial serial scan
d) Parallel scan
90. What are the two tenets in LSSD?
a. The circuit is level-sensitive.
b. Each register may be converted to a serial shift register.
91. What are the self-test techniques?
a. Signature analysis and BILBO
b. Memory self-test
c. Iterative logic array testing
92. What is known as BILBO?
Signature analysis can be merged with the scan technique to create a
structure known as BILBO- for Built In Logic Block Observation.
93. What is known as IDDQ testing?
A popular method of testing for bridging faults is called IDDQ or currentsupply
monitoring. This relies on the fact that when a complementary CMOS
logic gate is not switching, it draws no DC current. When a bridging fault occurs,
for some combination of input conditions a measurable DC IDD will flow.
94. What are the applications of chip level test techniques?
a. Regular logic arrays
b. Memories
c. Random logic
95. What is boundary scan?
The increasing complexity of boards and the movement to technologies
like multichip modules and surface-mount technologies resulted in system
designers agreeing on a unified scan-based methodology for testing chips at the
board. This is called boundary scan.
96. What is the test access port?
The Test Access Port (TAP) is a definition of the interface that needs to be
included in an IC to make it capable of being included in a boundary-scan
architecture. The port has four or five single bit connections, as follows:
• TCK(The Test Clock Input)
• TMS(The Test Mode Select)
• TDI(The Test Data Input)
• TDO(The Test Data Output)
It also has an optional signal
• TRST*(The Test Reset Signal)
97. What are the contents of the test architecture?
The test architecture consists of:
• The TAP interface pins
• A set of test-data registers
• An instruction register
• A TAP controller
98. What is the TAP controller?
The TAP controller is a 16-state FSM that proceeds from state to state
based on the TCK and TMS signals. It provides signals that control the test data
registers, and the instruction register. These include serial-shift clocks and update
clocks.
99. What is known as test data register?
The test-data registers are used to set the inputs of modules to be tested,
and to collect the results of running tests.
100. What is known as boundary scan register?
The boundary scan register is a special case of a data register. It allows
circuit-board interconnections to be tested, external components tested, and the
state of chip digital I/Os to be sampled.
BIG QUESTIONS & ANSWERS
1. Derive the CMOS inverter DC characteristics and obtain the relationship for output
voltage at different region in the transfer characteristics.
Explanation (2)
Diagram (2)
CMOS inverter (2)
DC characteristics (5)
Transfer characteristics (5)
2. Explain with neat diagrams the various CMOS fabrication technology
P-well process (4)
N-well process (4)
Silicon-On-Insulator Process (4)
Twin- tub Process (4)
3. Explain the latch up prevention techniques.
Definition (2)
Explanation (2)
Diagram (2)
4. Explain the operation of PMOS Enhancement transistor
Explanation (2)
Diagram (2)
Operation (4)
5. Explain the threshold voltage equation
Definition (2)
Explanation (2)
Derivation (4)
6. Explain the silicon semiconductor fabrication process.
Silicon wafer Preparation (2)
Epitaxial Growth (2)
Oxidation (2)
Photolithography (2)
Diffusion(2)
Ion Implantation (2)
Isolation technique (2)
Metallization (1)
Assembly processing & Packaging (1)
7. Explain various CAD tool sets.
Layout editors (4)
Design Rule checkers (DRC) (4)
Circuit extraction (4)
8. Explain the operation of NMOS Enhancement transistor.
Explanation (2)
Diagram (2)
Operation (4)
9. Explain the Transmission gate and the tristate inverter briefly.
Explanation (2)
Diagram (2)
Operation (4)
10. Explain about the various non ideal conditions in MOS device model.
Explanation (2)
Diagram (2)
Operation (4)
11. Explain the design hierarchies.
Explanation (2)
Diagram (2)
Concept (2)
12. Explain the concept involved in Timing control in VERILOG.
Explanation (2)
Diagram (2)
Delay-based timing control (4)
Event-based timing control(4)
Level-sensitive timing control(4)
13. Explain with neat diagrams the Multiplexer and latches using transmission
Gate.
Explanation (2)
Diagram (2)
Multiplexer (4)
latches(4)
14. Explain the concept of gate delay in VERILOG with example
Explanation (2)
Diagram (2)
Concept (2)
15. Explain the concept of MOSFET as switches and also bring the various logic
gates using the switching concept .
Explanation (2)
Diagram (2)
Gate Concepts (4)
16. Explain the concept involved in structural gate level modeling and also give the
description for Half adder and Full adder.
Explanation (2)
Diagram (2)
Gate Concepts (6)
Half adder (3)
Full adder (3)
17. What is ASIC? Explain the types of ASIC.
Definition (2)
Types (2)
Full custom ASICs (4)
Semi-custom ASICs(4)
Programmable ASICs(4)
18. Explain the VLSI design flow with a neat diagram
Explanation (2)
Flow Diagram (2)
Concepts (4)
19. Explain the concept of MOSFET as switches
Explanation (2)
Diagram (2)
Concepts (4)
20. Explain the ASIC design flow with a neat diagram
h. Design entry(2)
i. Logic synthesisSystem partitioning(2)
j. Prelayout simulation. (2)
k. Floorplanning(2)
l. Placement(2)
m. Routing(2)
n. Extraction (2)
2. Postlayout simulation(2)
21. a) Explain fault models.
Stuck-At Faults
Definition (2)
Diagram (2)
Short-circuit and Open-circuit faults
Definition (2)
Diagram (2)
b) Explain ATPG.
Definition (2)
Truth tables (2)
Five valued logic (2)
Testability measures (2)
22. Briefly explain
a) Fault grading & fault simulation
Fault grading (2)
Fault simulation (2)
b) Delay fault testing
Diagram (2)
Description (2)
c) Statistical fault analysis
Definition (1)
Statistics (3)
d) Fault sampling (4)
23. Explain scan-based test techniques.
Level sensitive scan design (4)
Serial scan (4)
Partial serial scan (4)
Parallel scan (4)
24. Explain Ad-Hoc testing and chip level test techniques.
Ad-Hoc testing
Parallel-load feature (2)
Test signal block (2)
Use of the bus (2)
Use of multiplexer (2)
Chip level test techniques
Definition (2)
Regular logic arrays (2)
Memories (2)
Random logic (2)
25. Explain self-test techniques and IDDQ testing.
Signature analysis and BILBO (6)
Memory-self test (4)
Iterative logic array testing (3)
IDDQ testing (3)
26. Explain system-level test techniques.
Boundary scan – definition (2)
The Test Access Port (2)
The Test Architecture (2)
The TAP Controller (3)
The Instruction Register (2)
Test-Data Registers (2)
Boundary Scan Registers (3)
KEYWORDS:VLSI DESIGN,VLSI DESIGN QUESTION PAPER,ANNA UNIVERSITY QUESTION PAPER,ANNA UNIVERSITY,ANNA UNIVERSITY CHENNAI,ANNA UNIVERSITY COIMBATORE,ANNA UNIVERSITY TRICHY,ANNA UNIVERSITY TIRUNELVELI,ANNA UNIVERSITY MADURAI,ANNA UNIVERSITY SYLLABUS,ANNA-UNIVERSITY RESULTS,ANNA UNIVERSITY DISTANCE EDUCATION,ANNA UNIVERSITY MBA-CENTRE FOR DISTANCE EDUCATION,ANNA UNIVERSITY SCHEDULE OF EXAMINATIONS,ANNA UNIVERSITY ADMISSION,ANNA UNIVERSITY COURSES,ANNA UNIVERSITY ACADEMIC,ANNA UNIVERSITY DEPARTMENTS,ANNA UNIVERSITY RESEARCH,ANNA UNIVERSITY MAIL,ANNA UNIVERSITY QUESTION PAPERS,ANNA UNIVERSITY COUNSELLING DATES,ANNA UNIVERSITY RE-EVALUATION RESULTS
DEPARTMENT OF ECE
EC 1401 – VLSI DESIGN
TWO MARK & BIG QUESTIONS WITH ANSWERS
COMPILED BY
V.S.DHARUN
LECTURER,ECE
2 MARK QUESTIONS & ANSWERS
1.What are four generations of Integration Circuits?
SSI (Small Scale Integration)
MSI (Medium Scale Integration)
LSI (Large Scale Integration)
VLSI (Very Large Scale Integration)
2.Give the advantages of IC?
Size is less
High Speed
Less Power Dissipation
3.Give the variety of Integrated Circuits?
More Specialized Circuits
Application Specific Integrated Circuits(ASICs)
Systems-On-Chips
4.Give the basic process for IC fabrication
Silicon wafer Preparation
Epitaxial Growth
Oxidation
Photolithography
Diffusion
Ion Implantation
Isolation technique
Metallization
Assembly processing & Packaging
5.What are the various Silicon wafer Preparation?
Crystal growth & doping
Ingot trimming & grinding
Ingot slicing
Wafer polishing & etching
Wafer cleaning.
6.Different types of oxidation?
Dry & Wet Oxidation
7.What is the transistors CMOS technology provides?
n-type transistors & p-type transistors.
8.What are the different layers in MOS transistors?
Drain , Source & Gate
9.What is Enhancement mode transistor?
The device that is normally cut-off with zero gate bias.
10. What is Depletion mode Device?
The Device that conduct with zero gate bias.
11.When the channel is said to be pinched –off?
If a large Vds is applied this voltage with deplete the Inversion layer .This Voltage
effectively pinches off the channel near the drain.
12.Give the different types of CMOS process?
p-well process
n-well process
Silicon-On-Insulator Process
Twin- tub Process
13.What are the steps involved in twin-tub process?
Tub Formation
Thin-oxide Construction
Source & Drain Implantation
Contact cut definition
Metallization.
14.What are the advantages of Silicon-on-Insulator process?
No Latch-up
Due to absence of bulks transistor structures are denser than bulk silicon.
15.What is BiCMOS Technology?
It is the combination of Bipolar technology & CMOS technology.
16.What are the basic processing steps involved in BiCMOS process?
Additional masks defining P base region
N Collector area
Buried Sub collector (SCCD)
Processing steps in CMOS process
17.What are the advantages of CMOS process?
Low power Dissipation
High Packing density
Bi directional capability
18.What are the advantages of CMOS process?
Low Input Impedance
Low delay Sensitivity to load.
19.What is the fundamental goal in Device modeling?
To obtain the functional relationship among the terminal electrical variables of the
device that is to be modeled.
20.Define Short Channel devices?
Transistors with Channel length less than 3- 5 microns are termed as Short channel
devices. With short channel devices the ratio between the lateral & vertical dimensions
are reduced.
21.What is pull down device?
A device connected so as to pull the output voltage to the lower supply voltage usually
0V is called pull down device.
22.Whateas.
29. Compare between CMOS and bipolar technologies.
CMOS Technology Bipolar technology
• Low static power dissipation
• High input impedance (low drive
current)
• Scalable threshold voltage
• High noise margin
• High packing density
• High delay sensitivity to load (fanout
limitations)
• Low output drive current
• Low gm (gm a Vin)
• Bidirectional capability
• A near ideal switching device
• High power dissipation
• Low input impedance (high drive
current)
• Low voltage swing logic
• Low packing density
• Low delay sensitivity to load
• High output drive current
• High gm (gm a eVin)
• High ft at low current
• Essentially unidirectional
30.Define Threshold voltage in CMOS?
The Threshold voltage, VT for a MOS transistor can be defined as the voltage applied
between the gate and the source of the MOS transistor below which the drain to
source current, IDS effectively drops to zero.
31.What is Body effect?
The threshold volatge VT is not a constant w. r. to the voltage difference between the
substrate and the source of MOS transistor. This effect is called substrate-bias effect or
body effect.
32.What is Channel-length modulation?
The current between drain and source terminals is constant and independent of the
applied voltage over the terminals. This is not entirely correct. The effective length of the
conductive channel is actually modulated by the applied VDS, increasing VDS causes the
depletion region at the drain junction to grow, reducing the length of the effective
channel.
33. What is Latch – up?
Latch up is a condition in which the parasitic components give rise to the establishment
of low resistance conducting paths between VDD and VSS with disastrous results. Careful
control during fabrication is necessary to avoid this problem.
34. Give the basic inverter circuit.
35. Give the CMOS inverter DC transfer characteristics and operating regions
36.Define Rise time
Rise time, tr is the time taken for a waveform to rise from 10% to 90% of its steady-state
value.
37. Define Fall time
Fall time, tf is the time taken for a waveform to fall from 90% to 10% of its steady-state
value.
38. Define Delay time
Delay time, td is the time difference between input transition (50%) and the 50% output
level. This is the time taken for a logic transition to pass from input to output.
39. What are two components of Power dissipation.
There are two components that establish the amount of power dissipated in a
CMOS circuit. These are:
i) Static dissipation due to leakage current or other current drawn
continuously from the power supply.
ii) Dynamic dissipation due to
- Switching transient current
- Charging and discharging of load capacitances.
40. Give some of the important CAD tools.
Some of the important CAD tools are:
i) Layout editors
ii) Design Rule checkers (DRC)
iii) Circuit extraction
41.What is Verilog?
Verilog is a general purpose hardware descriptor language. It is similar in syntax
to the C programming language. It can be used to model a digital system at many
levels of abstraction ranging from the algorithmic level to the switch level.
42. What are the various modeling used in Verilog?
1. Gate-level modeling
2. Data-flow modeling
3. Switch-level modeling
4. Behavioral modeling
43. What is the structural gate-level modeling?
Structural modeling describes a digital logic networks in terms of the components
that make up the system. Gate-level modeling is based on using primitive logic
gates and specifying how they are wired together.
44.What is Switch-level modeling?
Verilog allows switch-level modeling that is based on the behavior of MOSFETs.
Digital circuits at the MOS-transistor level are described using the MOSFET
switches.
45. What are identifiers?
Identifiers are names of modules, variables and other objects that we can
reference in the design. Identifiers consists of upper and lower case letters, digits
0 through 9, the underscore character(_) and the dollar sign($). It must be a single
group of characters.
Examples:
A014, a ,b, in_o, s_out
46. What are the value sets in Verilog?
Verilog supports four levels for the values needed to describe hardware referred to
as value sets.
Value levels
Condition in hardware circuits
0 Logic zero, false condition
1 Logic one, true condition
X Unknown logic value
Z High impedance, floating state
47. What are the types of gate arrays in ASIC?
1) Channeled gate arrays
2) Channel less gate arrays
3) Structured gate arrays
48. Give the classifications of timing control?
Methods of timing control:
1. Delay-based timing control
2. Event-based timing control
3. Level-sensitive timing control
Types of delay-based timing control:
1. Regular delay control
2. Intra-assignment delay control
3. Zero delay control
Types of event-based timing control:
1. Regular event control
2. Named event control
3. Event OR control
4. Level-sensitive timing control
49 Give the different arithmetic operators?
Operator symbol Operation performed Number of operands
* Multiply Two
/ Divide Two
+ Add Two
- Subtract Two
% Modulus Two
** Power (exponent) Two
50. Give the different bitwise operators.
Operator symbol Operation performed Number of operands
~ Bitwise negation One
& Bitwise and Two
| Bitwise or Two
^ Bitwise xor Two
^~ or ~^ Bitwise xnor Two
~& Bitwise nand Two
~| Bitwise nor Two
51. What are gate primitives?
Verilog supports basic logic gates as predefined primitives. Primitive logic
function keyword provide the basics for structural modeling at gate level. These
primitives are instantiated like modules except that they are predefined in verilog
and do not need a module definition. The important operations are and, nand, or,
xor, xnor, and buf(non-inverting drive buffer).
52. Give the two blocks in behavioral modeling.
1. An initial block executes once in the simulation and is used to set up
initial conditions and step-by-step data flow
2. An always block executes in a loop and repeats during the simulation.
53. What are the types of conditional statements?
1. No else statement
Syntax : if ( [expression] ) true – statement;
2. One else statement
Syntax : if ( [expression] ) true – statement;
else false-statement;
3. Nested if-else-if
Syntax : if ( [expression1] ) true statement 1;
else if ( [expression2] ) true-statement 2;
else if ( [expression3] ) true-statement 3;
else default-statement;
The [expression] is evaluated. If it is true (1 or a non-zero value) true-statement is
executed. If it is false (zero) or ambiguous (x), the false-statement is executed.
54. Name the types of ports in Verilog
Types of port Keyword
Input port Input
Output port Output
Bidirectional port inout
55. What are the types of procedural assignments?
1. Blocking assignment
2. Non-blocking assignment
56. Give the different symbols for transmission gate.
57. Give the different types of ASIC.
1. Full custom ASICs
2. Semi-custom ASICs
* standard cell based ASICs
* gate-array based ASICs
3. Programmable ASICs
* Programmable Logic Device (PLD)
* Field Programmable Gate Array (FPGA).
58. What is the full custom ASIC design?
In a full custom ASIC, an engineer designs some or all of the logic cells, circuits or
layout specifically for one ASIC. It makes sense to take this approach only if there
are no suitable existing cell libraries available that can be used for the entire design.
59. What is the standard cell-based ASIC design?
A cell-based ASIC (CBIC) USES PREDESIGNED LOGIC CELLS KNOWN AS
STANDARD CELLS. The standard cell areas also called fle4xible blocks in a CBIC
are built of rows of standard cells. The ASIC designer defines only the placement of
standard cells and the interconnect in a CBIC. All the mask layers of a CBIC are
customized and are unique to a particular customer.
60. Differentiate between channeled & channel less gate array.
Channeled Gate Array Channel less Gate Array
1. Only the interconnect is customized
Only the top few mask layers are
customized.
2. The interconnect uses predefined
spaces between rows of base cells.
No predefined areas are set aside for routing
between cells.
3. Routing is done using the spaces Routing is done using the area of transistors
unused.
4. Logic density is less Logic density is higher.
61. Give the constituent of I/O cell in 22V10.
2V10 I/O cell consists of
1. a register
2. an output 4:1 mux
3. a tristate buffer
4. a 2:1 input mux
It has the following characteristics:
* 12 inputs
* 10 I/Os
* product time 9 10 12 14 16 14 12 10 8
* 24 pins
62. What is a FPGA?
A field programmable gate array (FPGA) is a programmable logic device that
supports implementation of relatively large logic circuits. FPGAs can be used to
implement a logic circuit with more than 20,000 gates whereas a CPLD can implement
circuits of upto about 20,000 equivalent gates.
63. What are the different methods of programming of PALs?
The programming of PALs is done in three main ways:
• Fusible links
• UV – erasable EPROM
• EEPROM (E2PROM) – Electrically Erasable Programmable ROM
64.What is an antifuse?
An antifuse is normally high resistance (>100MW). On application of appropriate
programming voltages, the antifuse is changed permanently to a low-resistance
structure (200-500W).
65. What are the different levels of design abstraction at physical design.
• Architectural or functional level
• Register Transfer-level (RTL)
• Logic level
• Circuit level
66.What are macros?
The logic cells in a gate-array library are often called macros.
67. What are Programmable Interconnects ?
In a PAL, the device is programmed by changing the characteristics if the switching
element. An alternative would be to program the routing.
68. Give the steps inASIC design flow.
a. Design entry
b. Logic synthesisSystem partitioning
c. Prelayout simulation.
d. Floorplanning
e. Placement
f. Routing
g. Extraction
1. Postlayout simulation
69. Give the XILINX Configurable Logic Block .
70. Give the XILINX FPGA architecture
71. Mention the levels at which testing of a chip can be done?
a) At the wafer level
b) At the packaged-chip level
c) At the board level
d) At the system level
e) In the field
72.What are the categories of testing?
a) Functionality tests
b) Manufacturing tests
73. Write notes on functionality tests?
Functionality tests verify that the chip performs its intended function.
These tests assert that all the gates in the chip, acting in concert, achieve a desired
function. These tests are usually used early in the design cycle to verify the
functionality of the circuit.
74. Write notes on manufacturing tests?
Manufacturing tests verify that every gate and register in the chip
functions correctly. These tests are used after the chip is manufactured to verify
that the silicon is intact.
75. Mention the defects that occur in a chip?
a) layer-to-layer shorts
b) discontinous wires
c) thin-oxide shorts to substrate or well
76. Give some circuit maladies to overcome the defects?
a. nodes shorted to power or ground
b. nodes shorted to each other
c. inputs floating/outputs disconnected
77. What are the tests for I/O integrity?
a. I/O level test
b. Speed test
c. IDD test
78. What is meant by fault models?
Fault model is a model for how faults occur and their impact on circuits.
79. Give some examples of fault models?
a. Stuck-At Faults
b. Short-Circuit and Open-Circuit Faults
80. What is stuck – at fault?
With this model, a faulty gate input is modeled as a “stuck at zero” or
“stuck at one”. These faults most frequently occur due to thin-oxide shorts or
metal-to-metal shorts.
81. What is meant by observability?
The observability of a particular internal circuit node is the degree to
which one can observe that node at the outputs of an integrated circuit.
82. What is meant by controllability?
The controllability of an internal circuit node within a chip is a measure of
the ease of setting the node to a 1 or 0 state.
83. What is known as percentage-fault coverage?
The total number of nodes that, when set to 1 or 0, do result in the
detection of the fault, divided by the total number of nodes in the circuit, is called
the percentage-fault coverage.
84. What is fault grading?
Fault grading consists of two steps. First, the node to be faulted is selected.
A simulation is run with no faults inserted, and the results of this simulation are
saved. Each node or line to be faulted is set to 0 and then 1 and the test vector set
is applied. If and when a discrepancy is detected between the faulted circuit
response and the good circuit response, the fault is said to be detected and the
simulation is stopped.
85. Mention the ideas to increase the speed of fault simulation?
a. parallel simulation
b. concurrent simulation
86. What is fault sampling?
An approach to fault analysis is known as fault sampling. This is used in
circuits where it is impossible to fault every node in the circuit. Nodes are
randomly selected and faulted. The resulting fault detection rate may be
statistically inferred from the number of faults that are detected in the fault set and
the size of the set. The randomly selected faults are unbiased. It will determine
whether the fault coverage exceeds a desired level.
87. What are the approaches in design for testability?
a. ad hoc testing
b. scan-based approaches
c. self-test and built-in testing
88. Mention the common techniques involved in ad hoc testing?
a. partitioning large sequential circuits
b. adding test points
c. adding multiplexers
d. providing for easy state reset
89. What are the scan-based test techniques?
a) Level sensitive scan design
b) Serial scan
c) Partial serial scan
d) Parallel scan
90. What are the two tenets in LSSD?
a. The circuit is level-sensitive.
b. Each register may be converted to a serial shift register.
91. What are the self-test techniques?
a. Signature analysis and BILBO
b. Memory self-test
c. Iterative logic array testing
92. What is known as BILBO?
Signature analysis can be merged with the scan technique to create a
structure known as BILBO- for Built In Logic Block Observation.
93. What is known as IDDQ testing?
A popular method of testing for bridging faults is called IDDQ or currentsupply
monitoring. This relies on the fact that when a complementary CMOS
logic gate is not switching, it draws no DC current. When a bridging fault occurs,
for some combination of input conditions a measurable DC IDD will flow.
94. What are the applications of chip level test techniques?
a. Regular logic arrays
b. Memories
c. Random logic
95. What is boundary scan?
The increasing complexity of boards and the movement to technologies
like multichip modules and surface-mount technologies resulted in system
designers agreeing on a unified scan-based methodology for testing chips at the
board. This is called boundary scan.
96. What is the test access port?
The Test Access Port (TAP) is a definition of the interface that needs to be
included in an IC to make it capable of being included in a boundary-scan
architecture. The port has four or five single bit connections, as follows:
• TCK(The Test Clock Input)
• TMS(The Test Mode Select)
• TDI(The Test Data Input)
• TDO(The Test Data Output)
It also has an optional signal
• TRST*(The Test Reset Signal)
97. What are the contents of the test architecture?
The test architecture consists of:
• The TAP interface pins
• A set of test-data registers
• An instruction register
• A TAP controller
98. What is the TAP controller?
The TAP controller is a 16-state FSM that proceeds from state to state
based on the TCK and TMS signals. It provides signals that control the test data
registers, and the instruction register. These include serial-shift clocks and update
clocks.
99. What is known as test data register?
The test-data registers are used to set the inputs of modules to be tested,
and to collect the results of running tests.
100. What is known as boundary scan register?
The boundary scan register is a special case of a data register. It allows
circuit-board interconnections to be tested, external components tested, and the
state of chip digital I/Os to be sampled.
BIG QUESTIONS & ANSWERS
1. Derive the CMOS inverter DC characteristics and obtain the relationship for output
voltage at different region in the transfer characteristics.
Explanation (2)
Diagram (2)
CMOS inverter (2)
DC characteristics (5)
Transfer characteristics (5)
2. Explain with neat diagrams the various CMOS fabrication technology
P-well process (4)
N-well process (4)
Silicon-On-Insulator Process (4)
Twin- tub Process (4)
3. Explain the latch up prevention techniques.
Definition (2)
Explanation (2)
Diagram (2)
4. Explain the operation of PMOS Enhancement transistor
Explanation (2)
Diagram (2)
Operation (4)
5. Explain the threshold voltage equation
Definition (2)
Explanation (2)
Derivation (4)
6. Explain the silicon semiconductor fabrication process.
Silicon wafer Preparation (2)
Epitaxial Growth (2)
Oxidation (2)
Photolithography (2)
Diffusion(2)
Ion Implantation (2)
Isolation technique (2)
Metallization (1)
Assembly processing & Packaging (1)
7. Explain various CAD tool sets.
Layout editors (4)
Design Rule checkers (DRC) (4)
Circuit extraction (4)
8. Explain the operation of NMOS Enhancement transistor.
Explanation (2)
Diagram (2)
Operation (4)
9. Explain the Transmission gate and the tristate inverter briefly.
Explanation (2)
Diagram (2)
Operation (4)
10. Explain about the various non ideal conditions in MOS device model.
Explanation (2)
Diagram (2)
Operation (4)
11. Explain the design hierarchies.
Explanation (2)
Diagram (2)
Concept (2)
12. Explain the concept involved in Timing control in VERILOG.
Explanation (2)
Diagram (2)
Delay-based timing control (4)
Event-based timing control(4)
Level-sensitive timing control(4)
13. Explain with neat diagrams the Multiplexer and latches using transmission
Gate.
Explanation (2)
Diagram (2)
Multiplexer (4)
latches(4)
14. Explain the concept of gate delay in VERILOG with example
Explanation (2)
Diagram (2)
Concept (2)
15. Explain the concept of MOSFET as switches and also bring the various logic
gates using the switching concept .
Explanation (2)
Diagram (2)
Gate Concepts (4)
16. Explain the concept involved in structural gate level modeling and also give the
description for Half adder and Full adder.
Explanation (2)
Diagram (2)
Gate Concepts (6)
Half adder (3)
Full adder (3)
17. What is ASIC? Explain the types of ASIC.
Definition (2)
Types (2)
Full custom ASICs (4)
Semi-custom ASICs(4)
Programmable ASICs(4)
18. Explain the VLSI design flow with a neat diagram
Explanation (2)
Flow Diagram (2)
Concepts (4)
19. Explain the concept of MOSFET as switches
Explanation (2)
Diagram (2)
Concepts (4)
20. Explain the ASIC design flow with a neat diagram
h. Design entry(2)
i. Logic synthesisSystem partitioning(2)
j. Prelayout simulation. (2)
k. Floorplanning(2)
l. Placement(2)
m. Routing(2)
n. Extraction (2)
2. Postlayout simulation(2)
21. a) Explain fault models.
Stuck-At Faults
Definition (2)
Diagram (2)
Short-circuit and Open-circuit faults
Definition (2)
Diagram (2)
b) Explain ATPG.
Definition (2)
Truth tables (2)
Five valued logic (2)
Testability measures (2)
22. Briefly explain
a) Fault grading & fault simulation
Fault grading (2)
Fault simulation (2)
b) Delay fault testing
Diagram (2)
Description (2)
c) Statistical fault analysis
Definition (1)
Statistics (3)
d) Fault sampling (4)
23. Explain scan-based test techniques.
Level sensitive scan design (4)
Serial scan (4)
Partial serial scan (4)
Parallel scan (4)
24. Explain Ad-Hoc testing and chip level test techniques.
Ad-Hoc testing
Parallel-load feature (2)
Test signal block (2)
Use of the bus (2)
Use of multiplexer (2)
Chip level test techniques
Definition (2)
Regular logic arrays (2)
Memories (2)
Random logic (2)
25. Explain self-test techniques and IDDQ testing.
Signature analysis and BILBO (6)
Memory-self test (4)
Iterative logic array testing (3)
IDDQ testing (3)
26. Explain system-level test techniques.
Boundary scan – definition (2)
The Test Access Port (2)
The Test Architecture (2)
The TAP Controller (3)
The Instruction Register (2)
Test-Data Registers (2)
Boundary Scan Registers (3)
KEYWORDS:VLSI DESIGN,VLSI DESIGN QUESTION PAPER,ANNA UNIVERSITY QUESTION PAPER,ANNA UNIVERSITY,ANNA UNIVERSITY CHENNAI,ANNA UNIVERSITY COIMBATORE,ANNA UNIVERSITY TRICHY,ANNA UNIVERSITY TIRUNELVELI,ANNA UNIVERSITY MADURAI,ANNA UNIVERSITY SYLLABUS,ANNA-UNIVERSITY RESULTS,ANNA UNIVERSITY DISTANCE EDUCATION,ANNA UNIVERSITY MBA-CENTRE FOR DISTANCE EDUCATION,ANNA UNIVERSITY SCHEDULE OF EXAMINATIONS,ANNA UNIVERSITY ADMISSION,ANNA UNIVERSITY COURSES,ANNA UNIVERSITY ACADEMIC,ANNA UNIVERSITY DEPARTMENTS,ANNA UNIVERSITY RESEARCH,ANNA UNIVERSITY MAIL,ANNA UNIVERSITY QUESTION PAPERS,ANNA UNIVERSITY COUNSELLING DATES,ANNA UNIVERSITY RE-EVALUATION RESULTS